Encore ENMGS-24+4 Podręcznik Użytkownika

ENMGS-24+4 24 Port Gigabit Web Smart Switch w/ 4 port mini GBIC User Guide 0

Installing Network Cables 1. Crossover or straight-through cable: All the ports on the switch support Auto-MDI/MDI-X functionality. Both straight-t

Functional Description Jumbo Frame With Jumbo Frame supported, it is allowed for the switch to transport identical data in fewer frames. Hence helps

Management guide Access the management interface of the Switch This section instructs you how to enter and proceed the advanced management capabili

1. Running your Web Browser and enter the IP address “192.168.1.1” in the Address field. 2. Key in the user name and password to pass the authent

Homepage After authentication procedure, the “SYSTEM Configuration” page shows up as the Homepage. You may click the hyperlinks on the left side of

System The System window provides the switch information and allows users to configure the switch properties. Items Functions MAC Address The

Port This Port Configuration page shows the link status of each port and allows users to configure speed, flow control and Max frame size for each p

functioning. Flow Control Mark the checkbox to enable the FDX Flow control, or unmark to disable. Max Frame length To adjust the size of Jumbo Fra

VLAN VLAN divides the network members into groups to reduce packets collisions and improve the network efficiency. The switch supports 802.1Q tag-ba

Note: 1. When a port is configured to a specific VLAN group, a PVID that corresponding to the VLAN id will be assigned automatically to this port. (

FCC Certifications This Equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FC

PVID When the VLAN-enabled switch receives a tagged packet, the packet will be sent to the port’s default VLAN according to the PVID (port VLAN ID)

Aggregation/ Trunk Configuration To set up the Port trunk groups, put the ports number into the same Aggregation group. There are eight groups to ch

Quality of Service QoS enhances the communication quality by giving different precedence to classified packets. This switch provides port-based, tag

Tag based QoS: The Tag based QoS decides packet priority according to the tags that adding on the packets. To configure Tag Based QoS configura

DSCP mode QoS: The DSCP mode QoS gives packet priority by the types of the incoming packets. We distinguish those packets according to the “Delay

Mirror The Mirror function copies all the packets that are transmitted by the source port to the destination port. It allows administrators to analy

Rate Limit This “Rate Limit” page allows users to limit the bandwidth for each port and configure the rules for Storm Control, which limits the flo

SNMP This device supports SNMP-management, which allows network administrators to monitor and configure this device with SNMP software. To allow thi

Discovery After installing series of our switches, the discovery management tool helps users to search and get access to those switches within the

Statistics Overview The Statistics Overview is provided for users to see the general transmitting and receiving status of each port. You may click

Table of Contents UNPACKING INFORMATION... 4 INTRODUCTION ... 4 GENERAL DESCRIPTION

Restart Restart: To restart the system, click the “Yes” button. The system restarts and shows the authentication window. Please fill in the userna

Software Upload This “Software Upload” page allows users to upgrade firmware for this switch. To perform firmware upgrade: 1. Click the “Browse”

Product Specifications Standard IEEE802.3 10BASE-T IEEE802.3u 100BASE-TX IEEE802.3x full-duplex operation and flow control IEEE802.3ab/z 1000BASE-T I

Appendix- Command Line Interface Start-up and Terminal configuration To start-up the command line interface, please connect a PC COM port to the RS

Command Hierarchy After logging in, press ? + <enter> to show the 9 command groups. System - System commands Console - Console

Command Description The following session introduces the command structure of the command line interface. Command groups: System - System co

[<name>]: String of up to 16 characters (default: Show user name). System Password [<password>] Description: Set or show the console pa

Port Commands Commands at Port level: Port Configuration [<portlist>] Port Mode [<portlist>] [<mode>] Port Flow Control [<portl

Port Admin [<portlist>] [enable|disable] Description: Set or show the admin state for the port. [<portlist>] : Port list (default: A

VLAN Commands Commands at VLAN level: VLAN Configuration [<portlist>] VLAN Add <vidlist> [<portlist>] VLAN Delete <vidlist>

DISCOVERY ...27 STATISTICS OVERVIEW ...

VLAN Egress [<portlist>] [untagged|tagged] Description: Set or show the VLAN egress mode setting for the port. Egress untagged ports will stri

Aggregation Commands Commands at Aggr level: Aggr Configuration Aggr Add <portlist> Aggr Delete <portlist> Aggr Lookup <portlist>

QoS Commands Commands at QoS level: QoS Configuration [<portlist>] QoS Mode [<portlist>] [tag|port|diffserv] QoS Port [<portlist&g

QoS DiffServ [<dscpno>] [<class>] Description: Set or show the IP Differentiated Services mapping. [<dscpno>]: IP DSCP number, 0-

IP Commands Commands at IP level: IP Configuration IP Setup [<ipaddress> [<ipmask> [<ipgateway>]]] [<vid>] IP Web managemen

SNMP Setup [enable|disable] Description: Activate or deactivate the SNMP. [enable|disable]: Enable/disable SNMP (default: Show SNMP mode). SNMP Tra

Ratelimit Egress [<portlist>] [enable|disable] [<rate>] Description: Set or show the egress configuration. [<portlist>] :

Unpacking Information Thank you for purchasing the 16/24-Port Gigabit Web Smart Switch with 4-Port Mini-GBIC. Before you start, please verify that yo

Key Features z 16/24 fixed 10/100/1000Mbps Gigabit Ethernet ports for easy network connecting application. z Equips 4 SFP ports for optional fiber

LED for each port: The switch provides one “1000M” LED and one “10/100M” LED for each port. 1000M LED: Shows the current transmitting/receiving

Restore Default Button You can use this button to reset the switch or restore factory default settings. To reset the switch, press the button once.

Installation This switch can be placed on your desktop directly, or mounted in a rack. Please refer to the instructions for installation. Before ins